Order Products : sales@su-jiao.com
OnFlex™ V 3085A-S0098
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | OnFlex™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 8GL2XO_OnFlex-V-3085A-S0098.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
| OnFlex™-V has the properties of traditional vulcanized rubber, but also has the processability of thermoplastic. Thermoplastic elastomer polymer OnFlex™-V 3000 series products are based on polyolefin phase and are distributed with cross-linked ethylene propylene diene monomer (EPDM) phase. This series of polymer products are specially manufactured to provide the melt strength and processability required for blow molding. In addition, the thermoplastic elastomer polymer OnFlex™-V 3000 series products have excellent coloring (light yellow), good mechanical properties, excellent buckling in a wide temperature range, large hardness range, good resistance to hydrocarbons, heat aging and weather resistance Good performance. |
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Density | 0.930 | g/cm³ | ISO 1183 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A) | 85 | ISO 868 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ISO 37 | ||
| 100% strain | 6.20 | MPa | ISO 37 |
| 300% strain | 7.90 | MPa | ISO 37 |
| Tensile Stress (Break) | 14.0 | MPa | ISO 37 |
| Tensile Elongation (Break) | 500 | % | ISO 37 |
| Compression Set | ISO 815 | ||
| 23°C, 72 hr | 38 | % | ISO 815 |
| 70°C, 22 hr | 57 | % | ISO 815 |
| 100°C, 22 hr | 60 | % | ISO 815 |
| Additional Information | Nominal Value | ||
|---|---|---|---|
| General Material Type | Thermoplastic vulcanized rubber (TPV) | ||
| 各项属性值是采用注射模制基板测量得出。 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 80.0 | °C | |
| Drying Time | 3.0 | hr | |
| Processing (Melt) Temp | 200 - 230 | °C | |
| Mold Temperature | 30.0 - 60.0 | °C | |
| Injection Rate | Fast |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Tecomid® NA40 NL E | Eurotec Engineering Plastics | Nylon 66 | Tecomid® |
| StarXTRUDE XTR-95-1000 | STAR Thermoplastic Alloys & Rubbers, Inc. | TPE | StarXTRUDE |
| Daelim Po1y® LH-402 | DAELIM INDUSTRIAL CO., LTD. | HDPE | Daelim Po1y® |
| FHR Polypropylene P4C6Z-059 | Flint Hills Resources, LP | PP Homopolymer | FHR Polypropylene |
| OTECH TPO OTO9097 - Cord Jacket | OTECH Corporation | TPO | OTECH TPO |
