Evoprene™ LF 6156 Datasheet,SBC,AlphaGary-SHANGHAI SUSHENG

Evoprene™ LF 6156

Category:	SBC , Styrene Butadiene Block Copolymer
Manufacturer:	AlphaGary
Trademark:	Evoprene™ LF
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	7VmpiA_Evoprene-LF-6156.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
Two ranges of HSBC based Evoprene™ TPE compounds have been created for the Automotive Industry, both specially formulated to have very low fogging characteristics suitable for automotive interior applications. Evoprene™ LF grades meet the requirements of the Reflectance Fogging test according to SAE J1756 whilst the Evoprene™ GF grades satisfy the DIN 75201B Gravimetric Fogging standard. Different automotive makers prefer different methods. All these Evoprene™ compounds are based on the well established hydrogenated styrene block copolymer (HSBC) TPE technology which offers a great blend of performance and processing characteristics to both automotive designers and processors alike. All grades can be injection moulded or extruded on standard thermoplastics equipment - full details are available in our Evoprene™ processing guides. Compounds can be formulated at various levels of UV resistance, depending on where in the vehicle the parts are to be used. Whilst they are normally supplied as natural for masterbatching, or black, Evoprene™ LF and GF compounds can be colour matched to specific automotive requirements when produced in longer compound runs. Heat ageing tests demonstrate these compounds are thermally stable to well beyond the maximum and minimum temperatures recorded in cars and trucks.

Message

Two ranges of HSBC based Evoprene™ TPE compounds have been created for the Automotive Industry, both specially formulated to have very low fogging characteristics suitable for automotive interior applications. Evoprene™ LF grades meet the requirements of the Reflectance Fogging test according to SAE J1756 whilst the Evoprene™ GF grades satisfy the DIN 75201B Gravimetric Fogging standard. Different automotive makers prefer different methods.

All these Evoprene™ compounds are based on the well established hydrogenated styrene block copolymer (HSBC) TPE technology which offers a great blend of performance and processing characteristics to both automotive designers and processors alike. All grades can be injection moulded or extruded on standard thermoplastics equipment - full details are available in our Evoprene™ processing guides. Compounds can be formulated at various levels of UV resistance, depending on where in the vehicle the parts are to be used. Whilst they are normally supplied as natural for masterbatching, or black, Evoprene™ LF and GF compounds can be colour matched to specific automotive requirements when produced in longer compound runs. Heat ageing tests demonstrate these compounds are thermally stable to well beyond the maximum and minimum temperatures recorded in cars and trucks.

General Information
Features	Block Copolymer Good Processability Good Thermal Stability Low to No Fogging
Uses	Automotive Applications Automotive Interior Parts Automotive Interior Trim Masterbatch
Agency Ratings	SAE J1756
RoHS Compliance	Contact Manufacturer
Appearance	Black Colors Available Natural Color
Forms	Pellets
Processing Method	Extrusion Injection Molding

Physical	Nominal Value	Unit	Test Method
Density	0.860 to 0.960	g/cm³	ISO 1183

Hardness	Nominal Value	Unit	Test Method
Shore Hardness (Shore A, 15 sec)	77		ISO 868

Elastomers	Nominal Value	Unit	Test Method
Tensile Set ¹(70°C, 1320 min)	77	%	Internal Method
Tensile Stress - Flow ²(100% Strain)	4.80	MPa	ISO 37
Tensile Stress - Flow ³(Yield)	9.10	MPa	ISO 37
Tensile Elongation - Flow ⁴(Break)	630	%	ISO 37
Tear Strength ⁵			ISO 34-1
Across Flow	57	kN/m
Flow	47	kN/m
Compression Set			ISO 815
23°C, 72 hr	27	%
70°C, 24 hr	45	%

Aging	Nominal Value	Unit	Test Method
Change in Tensile Strength in Air ⁶(100°C, 1000 hr)	-1.4	%	ISO 188
Change in Tensile Strain at Break in Air ⁷(100°C, 1000 hr)	-6.0	%	ISO 188
Change in Shore Hardness in Air ⁸(Shore A, 100°C, 1000 hr)	-2.0		ISO 188
Continuous Upper Temperature Resistance ⁹(3 hr)	170	°C
Change in Length in Air ¹⁰	-0.70	%	ISO 188
Change in Volume in Air ¹¹	3.0	%	ISO 188

Flammability	Nominal Value	Unit	Test Method
Fogging
Gravimetric	0.0	g	DIN 75201B
Reflectance ¹²	91	%	SAE J1756

Additional Information	Nominal Value		Test Method
Odor Rating - Dry ¹³	2.00		Multiple Standards
Ozone Resistance ¹⁴	0.00

Thermal	Nominal Value	Unit	Test Method
Brittleness Temperature	-60.0	°C	ASTM D746

Flammability	Nominal Value	Unit	Test Method
Burning Rate	54	mm/min

Note Message
1 .	VDA 675 217B
2 .	500 mm/min
3 .	500 mm/min
4 .	500 mm/min
5 .	Method Ba, Angle (Unnicked)
6 .	150+/- 50 air changes/hour
7 .	150+/- 50 air changes/hour
8 .	150+/- 50 air changes/hour
9 .	No distortion
10 .	150+/- 50 air changes/hour
11 .	150+/- 50 air changes/hour
12 .	3h heat @ 121°C, 21°C cooling plate, post test conditioning 1h & 16h
13 .	SAE J1351 / FLTM BO131-01
14 .	100 pphm/200 hr/ 20% strain

Resin Grade	Manufacturer	Category	Trademark
RTP 283 TFE 20	RTP Company	Nylon 66	RTP
TUFNYL® SGF 40 NATURAL	SRF Ltd.	Nylon 6	TUFNYL®
Ateva® 1821A	Celanese EVA Performance Polymers	EVA	Ateva®
PENTAMID B MK30 H natur	PENTAC Polymer GmbH	Nylon 6	PENTAMID B
StarClear® 1050-0000	Star Thermoplastic Alloys & Rubbers, Inc.	TPE	StarClear®

Resin Grade

Manufacturer