Order Products : sales@su-jiao.com
Versollan™ OM 1262NX-1
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | PolyOne Corporation |
| Trademark: | Versollan™ |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 78Meic_Versollan-OM-1262NX-1.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
Versollan™OM 1262NX-1 is a high-performance polyurethane (TPU) alloy designed for thin-walled overlapping molding with polycarbonate (PC), ABS, PC/ABS and other substrates.
|
| General Information | |
|---|---|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| RoHS Compliance |
|
| Appearance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.17 | g/cm³ | ASTM D792 |
| Melt Mass-Flow Rate (MFR) | ASTM D1238 | ||
| 190°C/2.16 kg | 11 | g/10 min | ASTM D1238 |
| 200°C/5.0 kg | 64 | g/10 min | ASTM D1238 |
| Molding Shrinkage - Flow | 0.90 - 1.5 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec) | 65 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress 1 | ASTM D412 | ||
| 100% strain, 23°C 2 | 2.55 | MPa | ASTM D412 |
| 300% strain, 23°C 3 | 3.34 | MPa | ASTM D412 |
| Tensile Strength (Break, 23°C) | 7.64 | MPa | ASTM D412 |
| Tensile Elongation (Break, 23°C) | 710 | % | ASTM D412 |
| Tear Strength | 40.3 | kN/m | ASTM D624 |
| Compression Set (23°C, 22 hr) | 35 | % | ASTM D395B |
| Flammability | Nominal Value | Test Method | |
|---|---|---|---|
| Flame Rating (1.50 mm) | HB | UL 94 |
| Fill Analysis | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Apparent Viscosity (200°C, 11200 sec^-1) | 20.0 | Pa·s | ASTM D3835 |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 48.9 - 54.4 | °C | |
| Drying Time | 3.0 - 4.0 | hr | |
| Suggested Max Moisture | < 0.030 | % | |
| Suggested Max Regrind | 20 | % | |
| Rear Temperature | 163 - 188 | °C | |
| Middle Temperature | 182 - 199 | °C | |
| Front Temperature | 188 - 210 | °C | |
| Nozzle Temperature | 193 - 216 | °C | |
| Mold Temperature | 21.1 - 37.8 | °C | |
| Back Pressure | 0.00 - 0.552 | MPa | |
| Screw Speed | 25 - 75 | rpm |
| Injection instructions |
|---|
| 或聚醚型聚氨酯为基础的色母料最适合 Versollan™ OM 1262NX-1 着色。典型的母料浓度为 50:1 到 25:1 - 要最大限度减少对硬度的影响，用量应该尽可能低。若使用 GLS 可供的预着色复合材料，则可达到较好的配色一致性。不推荐使用以聚丙烯 (PP) 为基础的色母料，因为其对 TPE 与基体之间的粘接会有显著影响。不应采用以 TPE 为基础的色母料。色母料是否适用，应由用户通过试验来最终确定。在使用此产品之前或之后，均须用熔体流动速率较低 (0.5 - 2.5 MFR) 的聚乙烯 (PE) 或聚丙烯 (PP) 彻底进行置换。Versollan™ OM 1262NX-1 可利用高达 20% 的回收料同时其性能所受影响却极小，但该回收料必须是未受到污染的。为了最大限度地减小模塑期间其性能所受的影响，熔体温度应维持得尽可能低。回收料的有效性应由用户最终确定。Versollan™ OM 1262NX-1 不应在机筒内闲置过长时间（5 分钟以上）。建议露点：-40°F注射速度：0.5 - 2 英寸/秒第一阶段 - 提升压力：200 - 900 psi第二阶段 - 保持压力：30% 的升压保持时间（厚部件）：4 - 10 秒保持时间（薄部件）：1 - 3 秒 |
| Note Message | |
|---|---|
| 1 . | 2 hours |
| 2 . | Mouth die c |
| 3 . | C mould |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Quadrant EPP Proteus® Black | Quadrant Engineering Plastic Products | PP Homopolymer | Quadrant EPP |
| Quadraflex™ ALE-95A-B20 | Biomerics, LLC | TPU-Polyether | Quadraflex™ |
| Yuyao PBT 518 | Yuyao Tenglong Plastics Co., Ltd. | PBT | Yuyao PBT |
| INEOS PP L70J-00 | INEOS Olefins & Polymers USA | PP Impact Copolymer | INEOS PP |
| Karina IVORY PVC COMPOUND 760-35/1-IS-SD | Karina Ind. e Com. de Plásticos Ltda | PVC, Unspecified | Karina |
