Order Products : sales@su-jiao.com
Makrolon® Sheet UV
| Category: | PC , Polycarbonate |
| Manufacturer: | Covestro - Polycarbonates |
| Trademark: | Makrolon® Sheet |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 6YwZL2_MakrolonSheetUV.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Makrolon® UV sheet is a transparent polycarbonate product with an advanced UV resistance technology that assures long lasting outdoor weathering performance in flat and curved glazing applications. It has higher impact resistance than acrylic and glass, and it can be cold-formed during installation. Makrolon UV is produced with high optical quality and minimal distortion in clear, a range of standard architectural tints, or can be custom matched to any color. Makrolon UV has a ten (10) year Limited Product Warranty against breakage, yellowing, and loss of light transmission. The terms of the warranty are available upon request. Applications Awnings, entryway canopies, skylights, barrel vaults, glazed archways, covered pedestrian walkways, and sloped, vertical, and curved glazing |
| General Information | |
|---|---|
| Additive |
|
| Features |
|
| Uses |
|
| Agency Ratings |
|
| Appearance |
|
| Forms |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.20 | g/cm³ | ASTM D792 |
| Water Absorption (24 hr) | 0.15 | % | ASTM D570 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Rockwell Hardness | ASTM D785 | ||
| Class m | 70 | ASTM D785 | |
| Class r | 118 | ASTM D785 |
| Mechanical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Modulus | 2340 | MPa | ASTM D638 |
| Tensile Strength | ASTM D638 | ||
| Yield | 62.1 | MPa | ASTM D638 |
| Limit | 65.5 | MPa | ASTM D638 |
| Tensile Elongation (Break) | 110 | % | ASTM D638 |
| Flexural Modulus | 2380 | MPa | ASTM D790 |
| Flexural Strength | 93.1 | MPa | ASTM D790 |
| Compressive Modulus | 2380 | MPa | ASTM D695 |
| Compressive Strength | 86.2 | MPa | ASTM D695 |
| Shear Modulus | 786 | MPa | ASTM D732 |
| Shear Strength | ASTM D732 | ||
| -- 1 | 68.9 | MPa | ASTM D732 |
| -- 2 | 41.4 | MPa | ASTM D732 |
| Poisson's Ratio | 0.38 | ASTM E132 | |
| Wear resistance- Delta Haze 3 | 2 | % | ASTM D1044 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Shading Coefficient | NFRC 100-2010 | ||
| Clear : 5.99 mm | 0.970 | NFRC 100-2010 | |
| Gray or Bronze : 5.99 mm | 0.770 | NFRC 100-2010 | |
| U Factor | NFRC 100-2010 | ||
| Summer : 5.99 mm | 0.850 | BTU/hr/ft²/°F | NFRC 100-2010 |
| Summer : 9.53 mm | 0.780 | BTU/hr/ft²/°F | NFRC 100-2010 |
| Winter : 5.99 mm | 0.920 | BTU/hr/ft²/°F | NFRC 100-2010 |
| Winter : 9.53 mm | 0.850 | BTU/hr/ft²/°F | NFRC 100-2010 |
| Flammability | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Flash Ignition Temperature | 440 | °C | ASTM D1929 |
| Horizontal Burn - AEB | cm | ASTM D635 | |
| Self Ignition Temperature | 550 | °C | ASTM D1929 |
| Impact | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Notched Izod Impact (3.18 mm) | 850 | J/m | ASTM D256 |
| Unnotched Izod Impact (3.18 mm) | No Break | ASTM D256 | |
| Instrumented Dart Impact (3.18 mm) | > 63.7 | J | ASTM D3763 |
| Thermal | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Deflection Temperature Under Load | ASTM D648 | ||
| 0.45 MPa, not annealed | 138 | °C | ASTM D648 |
| 1.8 MPa, not annealed | 132 | °C | ASTM D648 |
| Brittleness Temperature | -129 | °C | ASTM D746 |
| CLTE - Flow | 6.8E-5 | cm/cm/°C | ASTM D696 |
| Thermal Conductivity | 0.19 | W/m/K | ASTM C177 |
| Electrical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Volume Resistivity | 8.2E+16 | ohms·cm | ASTM D257 |
| Dielectric Strength (3.18 mm, in Air) | 15 | kV/mm | ASTM D149 |
| Dielectric Constant | ASTM D150 | ||
| 10 Hz | 2.96 | ASTM D150 | |
| 60 Hz | 3.17 | ASTM D150 | |
| Dissipation Factor (60 Hz) | 9.0E-4 | ASTM D150 | |
| Arc Resistance | ASTM D495 | ||
| -- 4 | 10.0 | sec | ASTM D495 |
| -- 5 | 120 | sec | ASTM D495 |
| Optical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Refractive Index | 1.586 | ASTM D542 | |
| Transmittance | ASTM D1003 | ||
| 3000 µm 6 | 86.0 | % | ASTM D1003 |
| 3000 µm 7 | 50.0 | % | ASTM D1003 |
| 3000 µm 8 | 50.0 | % | ASTM D1003 |
| 3000 µm 9 | 18.0 | % | ASTM D1003 |
| Note Message | |
|---|---|
| 1 . | Ultimate |
| 2 . | Yield |
| 3 . | 100 Cycles, CS-10F Wheel, 500 g load |
| 4 . | Steel Strip Electrode |
| 5 . | Tungsten Electrodes |
| 6 . | Clear |
| 7 . | I30 Gray |
| 8 . | K09 Bronze |
| 9 . | I35 Dark Gray |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| RTP 299 A X 92682 E | RTP Company | Nylon 6 | RTP |
| SABIC® LLDPE RG50035 | Saudi Basic Industries Corporation (SABIC) | LLDPE | SABIC® LLDPE |
| NYCOA Polyamide 4112 FR | Nycoa (Nylon Corporation of America) | Nylon 6 | NYCOA Polyamide |
| Grivory® XE 4164 black 9225 | EMS-GRIVORY | Nylon 10T/X | Grivory® |
| INEOS EMAA M21N430 | INEOS Olefins & Polymers Europe | EMAA | INEOS EMAA |
