Order Products : sales@su-jiao.com
RTP 6002-75A
| Category: | TPE , Thermoplastic Elastomer |
| Manufacturer: | RTP Company |
| Trademark: | RTP |
| Fillers: | - |
| Ports: | Qinzhou, Shekou, Shanghai, Ningbo |
| Delivery Terms | FOB, CIF, DAP, DAT, DDP |
| PDF: | 5Gfxyc_RTP-6002-75A.pdf  |
| PRICE: | Order Products email sales@su-jiao.com |
Wechat:
| Message |
|---|
|
Warning: The status of this material is 'Commercial: Limited Issue' The data for this material has not been recently verified. Please contact RTP Company for current information prior to specifying this grade. Bondable to PC/ABS, PC, ABS - 75 Shore A |
| General Information | |
|---|---|
| RoHS Compliance |
|
| Forms |
|
| Processing Method |
|
| Physical | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Specific Gravity | 1.04 | g/cm³ | ASTM D792 |
| Molding Shrinkage - Flow (3.20 mm) | 1.6 | % | ASTM D955 |
| Hardness | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Durometer Hardness (Shore A, 10 sec) | 75 | ASTM D2240 |
| Elastomers | Nominal Value | Unit | Test Method |
|---|---|---|---|
| Tensile Stress | ASTM D412 | ||
| 50% strain | 4.48 | MPa | ASTM D412 |
| 100% strain | 5.52 | MPa | ASTM D412 |
| 300% strain | 8.96 | MPa | ASTM D412 |
| Tensile Strength (Yield) | 13.1 | MPa | ASTM D412 |
| Tensile Elongation (Yield) | 500 | % | ASTM D412 |
| Tear Strength 1 | 59.5 | kN/m | ASTM D624 |
| Compression Set 2 | ASTM D395B | ||
| 23°C, 22 hr | 24 | % | ASTM D395B |
| 70°C, 22 hr | 71 | % | ASTM D395B |
| Additional Information |
|---|
| Bondable to PC/ABS, PC, ABSMoisture Content: 0.04%Peel Strength, ISO 813, 90°, 20 in/min, ABS, Overmold Failure: >35 pliPeel Strength, ISO 813, 90°, 20 in/min, PC, Overmold Failure: >35 pliPeel Strength, ISO 813, 90°, 20 in/min, PC/ABS, Interface Failure: 35 pli |
| Injection | Nominal Value | Unit | |
|---|---|---|---|
| Drying Temperature | 76.7 | °C | |
| Drying Time | 2.0 - 4.0 | hr | |
| Processing (Melt) Temp | 193 - 238 | °C | |
| Mold Temperature | 21.1 - 48.9 | °C | |
| Injection Pressure | 34.5 - 103 | MPa |
| Injection instructions |
|---|
| Desiccant Type Dryer Required. |
| Note Message | |
|---|---|
| 1 . | C mould |
| 2 . | Type 2 |
| Resin Grade | Manufacturer | Category | Trademark |
|---|---|---|---|
| Styrolution PS 158N/L | INEOS Styrolution Group GmbH | PS (GPPS) | Styrolution PS |
| U-polymer UG-100-20 | UNITIKA Plastics Division | Polyarylate | U-polymer |
| Bergamid™ A70 white | PolyOne Corporation | Nylon 66 | Bergamid™ |
| Axiall PVC 6651 | Axiall Corporation | PVC, Flexible | Axiall PVC |
| Evoprene™ G 952 | AlphaGary | SEBS | Evoprene™ G |
