LUVOCOM® 105-8617 Datasheet,TPE,LEHVOSS Group-SHANGHAI SUSHENG

Message
LUVOCOM®105-8617 is a thermoplastic elastomer (TPE) material,. This product is available in North America, Africa and the Middle East, Latin America, Europe or Asia Pacific,. LUVOCOM®The main characteristics of 105-8617 are: conductivity.

General Information
Features	Conductivity Heat conduction Static conduction
Appearance	Grey

Physical	Nominal Value	Unit	Test Method
Density	1.11	g/cm³	ISO 1183
Molding Shrinkage	0.60 - 1.2	%	DIN 16901
Water Absorption (23°C, 24 hr)	< 0.30	%

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A)	86		ISO 868

Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus	300	MPa	ISO 527-2
Tensile Stress (Break)	5.00	MPa	ISO 527-2
Tensile Strain (Yield)	20	%	ISO 527-2

Impact	Nominal Value	Unit	Test Method
Charpy Unnotched Impact Strength (23°C)	No Break		ISO 179/1fU

Thermal	Nominal Value	Unit	Test Method
Continuous Use Temperature	90.0	°C	UL 746B
Maximum operating temperature- Short Term	140	°C

Electrical	Nominal Value	Unit	Test Method
Insulation Resistance		ohms	IEC 60167

Thermal	Nominal Value	Unit	Test Method
Thermal Conductivity ¹	9.5	W/m/K

Electrical	Nominal Value	Unit	Test Method
Surface Resistivity	< 1.0E+7	ohms	IEC 60093

Injection	Nominal Value	Unit
Drying Temperature - Desiccant Dryer	85	°C
Drying Time - Desiccant Dryer	2.0 - 3.0	hr
Rear Temperature	160 - 185	°C
Middle Temperature	170 - 190	°C
Front Temperature	175 - 195	°C
Nozzle Temperature	180 - 200	°C
Processing (Melt) Temp	200	°C
Mold Temperature	25 - 55	°C

Injection instructions
General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing, the moisture level should not exceed 0.01%, otherwise molecular degradation may occur. As the material absorbs water very rapidly, originally sealed containers should only be opened immediately before processing. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Injection instructions

General In general LUVOCOM® can be processed on conventional injection moulding machines while observing the usual technical guidelines. Any added fibrous materials or fillers may have an abrasive effect. In this case the cylinder and screw should be protected against wear as is usual in the processing of reinforced thermoplastic materials. Lengthy dwell times for the melts in the cylinder should be avoided. Lower the temperatures during interruptions! Predrying (optional) It is advisable to predry the granulate with a suitable dryer immediately before processing. The granulate may absorb moisture from the air. Delivery Form & Storage Unless indicated otherwise, the material is delivered as 3mm-long pellets in sealed bags on pallets. Preferably storage should be effected in dry and normally temperatured rooms Additional Information During processing, the moisture level should not exceed 0.01%, otherwise molecular degradation may occur. As the material absorbs water very rapidly, originally sealed containers should only be opened immediately before processing. The processing notes provided merely represent a recommendation for general use. Due to the large variety of machines, geometries and volumes of parts, etc., it may be necessary to employ different settings according to the specific application. Please contact us for further information.

Note Message
1 .	Hot-Disk, 60x60x3 mm

Category:	TPE , Thermoplastic Elastomer
Manufacturer:	LEHVOSS Group
Trademark:	LUVOCOM®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	54ydD7_LUVOCOM1058617.pdf
PRICE:	Order Products email sales@su-jiao.com

Resin Grade	Manufacturer	Category	Trademark
THERMOLAST® K TC5PCZ (Series: AD/PA/CS)	KRAIBURG TPE	TPE	THERMOLAST® K
TUFNYL® SGF 30 WHITE	SRF Ltd.	Nylon 6	TUFNYL®
Ultraform® W 2320 0035	BASF Corporation	Acetal (POM) Copolymer	Ultraform®
Axiall PVC 19802	Axiall Corporation	PVC, Flexible	Axiall PVC
Fainplast PVC GS 75/T	Fainplast Compounds S.r.l	PVC, Unspecified	Fainplast PVC