Order Products : sales@su-jiao.com

ALCUDIA® LDPE PE-071

Category:	LDPE , Low Density Polyethylene
Manufacturer:	REPSOL
Trademark:	ALCUDIA® LDPE
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	3Kh83k_ALCUDIA-LDPE-PE-071.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
ALCUDIA® PE071 is a low density polyethylene grade, produced by high pressure autoclave technology, especially intended for extrusion coating. This material offers an adequate balance between easy processability, good organoleptic properties, excellent adhesion and low neck-in. It does not contain any additives. TYPICAL APPLICATIONS Extrusion coating. Coextruded thin film. Injection moulding. The excellent draw down properties of ALCUDIA® PE-071 allow high-speed coatings, up to 850 m/min and 5 g/m² at a maximum extrusion temperature of 330°C. This material has a very low neck-in throughout a wide range of extrusion conditions. Recommended melt temperature range for extrusion coating from 275 to 330°C. Temperature range for coextrusion depending on the processed polymers. Processing conditions should be optimised for each production line.

Message

ALCUDIA® PE071 is a low density polyethylene grade, produced by high pressure autoclave technology, especially intended for extrusion coating. This material offers an adequate balance between easy processability, good organoleptic properties, excellent adhesion and low neck-in. It does not contain any additives.

TYPICAL APPLICATIONS

Extrusion coating.

Coextruded thin film.

Injection moulding.

The excellent draw down properties of ALCUDIA® PE-071 allow high-speed coatings, up to 850 m/min and 5 g/m² at a maximum extrusion temperature of 330°C.
This material has a very low neck-in throughout a wide range of extrusion conditions.
Recommended melt temperature range for extrusion coating from 275 to 330°C.
Temperature range for coextrusion depending on the processed polymers.
Processing conditions should be optimised for each production line.

General Information
Features	Workability, good Good sensory characteristics Good adhesion Low shrinkage Compliance of Food Exposure No additive
Uses	Coating application
Agency Ratings	European food contact, not rated
Processing Method	Co-extrusion molding Extrusion coating Injection molding

Physical	Nominal Value	Unit	Test Method
Density (23°C)	0.919	g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)	8.5	g/10 min	ISO 1133

Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature	86.0	°C	ISO 306/A

Extrusion	Nominal Value	Unit
Melt Temperature	275 - 330	°C

Extrusion instructions
Maximum Coating Speed: 850 m/minMinimum Coating Weight: 5 g/m²Total Neck-in: 68 mm

Resin Grade	Manufacturer	Category	Trademark
SABIC® PPcompound G3220A	SABIC Innovative Plastics	PP, Unspecified	SABIC® PPcompound
Udel® P-3700 HC	Solvay Specialty Polymers	PSU	Udel®
FORMULA P FIB 3620/L SC	Putsch Kunststoffe GmbH	PP, Unspecified	FORMULA P
PLUSTEK PA3510M8	Polyram Ram-On Industries	Nylon 66	PLUSTEK
LNP™ STAT-KON™ RX05489 compound	SABIC Innovative Plastics	Nylon 66	LNP™ STAT-KON™