Dow Corning® QP1-230

Category:	Silicone , Silicone
Manufacturer:	Dow Corning Corporation
Trademark:	Dow Corning®
Fillers:	-
Ports:	Qinzhou, Shekou, Shanghai, Ningbo
Delivery Terms	FOB, CIF, DAP, DAT, DDP
PDF:	0G8e7o_DowCorningQP1230.pdf
PRICE:	Order Products email sales@su-jiao.com

Wechat: WECHAT

Message
Liquid Silicone Rubber materials for device and component fabrication in the healthcare industry. APPLICATIONS Dow Corning® QP1-2XX Liquid Silicone Rubbers (LSRs) are platinum-catalyzed, heat-cured materials designed for the fabrication of medical devices and device components and for short term applications. DESCRIPTION Dow Corning QP1-2XX LSRs are a series of two-part platinum-catalyzed silicone elastomers specifically designed for liquid injection molding. Each elastomer is supplied in a two-part kit (Part A and Part B), equal portions (by weight) of which must be thoroughly blended together prior to use. The elastomer is thermally cured via an addition-cure (platinum-catalyzed) reaction. When blended and cured as indicated, the resulting elastomer consists of cross-linked dimethyl and methyl-vinyl siloxane copolymers and reinforcing silica. The Dow Corning QP1-2XX LSRs are available in a range of nominal hardness from 30 to 70, Durometer-Shore A. The elastomers can be used without any post cure; although, if necessary, this may be employed to stabilize the final properties.Furthermore, the cured elastomers are heat stable up to 204°C (400°F), can be autoclaved, and exhibit high gas permeability compared with most thermoset elastomers and thermoplastics.

Message

Liquid Silicone Rubber materials for device and component fabrication in the healthcare industry.

APPLICATIONS
Dow Corning® QP1-2XX Liquid Silicone Rubbers (LSRs) are platinum-catalyzed, heat-cured materials designed for the fabrication of medical devices and device components and for short term applications.

DESCRIPTION
Dow Corning QP1-2XX LSRs are a series of two-part platinum-catalyzed silicone elastomers specifically designed for liquid injection molding. Each elastomer is supplied in a two-part kit (Part A and Part B), equal portions (by weight) of which must be thoroughly blended together prior to use. The elastomer is thermally cured via an addition-cure (platinum-catalyzed) reaction. When blended and cured as indicated, the resulting elastomer consists of cross-linked dimethyl and methyl-vinyl siloxane copolymers and reinforcing silica.

The Dow Corning QP1-2XX LSRs are available in a range of nominal hardness from 30 to 70, Durometer-Shore A. The elastomers can be used without any post cure; although, if necessary, this may be employed to stabilize the final properties.Furthermore, the cured elastomers are heat stable up to 204°C (400°F), can be autoclaved, and exhibit high gas permeability compared with most thermoset elastomers and thermoplastics.

General Information
Features	High Gas Permeability No frost Low viscosity Workability, good Fast molding cycle Fast curing Good coloring High pressure heating resistance Compliance of Food Exposure
Uses	Medical/nursing supplies
Agency Ratings	USP Class VI
Processing Method	Injection molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity	1.12	g/cm³	ASTM D792
Viscosity ¹
Part A	184	Pa·s
Part B	165	Pa·s

Hardness	Nominal Value	Unit	Test Method
Durometer Hardness (Shore A)	30		ASTM D2240

Elastomers	Nominal Value	Unit	Test Method
Tensile Stress (100% Strain)	0.500	MPa	ASTM D412
Tensile Strength	3.80	MPa	ASTM D412
Tensile Elongation (Break)	630	%	ASTM D412
Tear Strength ²	15.8	kN/m	ASTM D624

Note Message
1 .	10/s
2 .	B mould

Resin Grade	Manufacturer	Category	Trademark
Sasol Polymers PE HF150	Sasol Polymers	LLDPE	Sasol Polymers PE
Sylvin 8225-65 Natural	Sylvin Technologies Incorporated	PVC, Flexible	Sylvin
Nanjing Hongrui PA6 B303	Nanjing Hongrui Engineering Plastics Co., Ltd.	Nylon 6	Nanjing Hongrui PA6
AIE PA66 60G3ST	Asia International Enterprise (Hong Kong) Limited	Nylon 66	AIE PA66
Edgetek™ AT-25GF/000 NC001	PolyOne Corporation	Acetal (POM) Copolymer	Edgetek™